Black Powder Coat
(Full Heim) Replaces the inner and outer tie rods. This kit comes with heims and both ends of the tie rods for a stronger and firmer feel. These are much stronger than stock tie rods and also eliminate bump steer.
(Outer Heim) Replaces the outer tie rod/ ball joint. This kit will tighten up the front end and steering. Connects to the stock inner tie rod. Runs a heim outer.
Specs:
Stock Replacement
Bolt-On

What's Included:
CNC Rack Bolt (Full Heim)
CNC Clevis (Full Heim)
Billet Tie Rods
Grade 8 Hardware
Stainless Misalignments
All Needed Heims

This spindle is meant to replace the existing spindle that comes with a 6" bracket lift. This spindle is fully fabricated and CAD designed. Designed for corrected steering position to help bump steer. No more shock contact due to steering arm position. Comes complete with full heim steering. This is a great upgrade for those that wheel with their bracket lifts. Built to order.

Note: With stock length control arms, this spindle will not work with 2.5" coilovers, only 2.0. Titan swap length works with both 2.0" and 2.5" coilovers

Specs: Lift: 6”

Minimum Rim Size: 16”

What's Included: Spindles

Billet Full Heim Steering

Grade 8 Hardware

Stainless Misalignments

All Needed Heims

Black Powder Coat

One piece CAD design with 5/16” plate. These shackles will give up to 2” of rear lift.

Specs:

Lift: 0-2” Lift

Stock Replacement

What's Included: Lift Shackles

Grade 8 Hardware

Black Powder Coat

This upper arm is meant to replace the stock arms. Theses arms allow for more coil bucket clearance when lifting your vehicle. The Titan Swap UCA come with heim pivots at the frame which allow for more wheel adjustment when aligning your vehicle. Comes with uniballs at the spindle pivot for more articulation and strength. Optional Delta Joint (614560) available for inclement weather areas. Arms come fully assembled for easy install.
Specs:
Lift: 0-3”
Minimum Rim Size: 16”
Maximum Tire Size: 35”
Track Width: + 3" per side

What's Included:
Tube UCA
Stainless Misalignments
Grade 8 Bolts
All Needed Heims and Uniballs
Black Powder Coat

Bolt-on electric fan setup for the Nissan Titans, Armadas, Frontiers, Xterras and Pathfinders. Comes with dual 2100 CFM (each) fans and dual electronic fan controller. This setup will work with both stock and CSF radiators. Comes with everything needed. Just remove the stock fan clutch and fan shroud, slide this setup in and wire in power and ground.

Specs:

Stock Replacement Fan Shroud

Drop in Ready

What's Included: Aluminum Fan Shroud

Dual 2100 CFM Fans

Electronic Dual Fan Controller

Dual Breakers

Probe Hose Kit

Replaces the outer tie rod/ ball joint. This kit will tighten up the front end and steering. Connects to the stock inner tie rod. Runs a heim outer.
Specs:
Stock Replacement
Bolt-On

What's Included:

Sold in pairs
Billet Tie Rods
Stainless Misalignments
Grade 8 Bolts
All Needed Heims

These mounts bolt under the hood to the existing hood hinge bolts. They come as a set. Come painted black.
Specs:
Bolt-On

What's Included:
Pair Pod Mounts
Painted Black

2.5 diameter coilover

Specifically designed for Titan swapped front ends.

Completely rebuild-able shock.

Spring rates available: 600lbs, 650lbs, 700lbs. When choosing your spring rate, please add to the notes the rate you choose.

Sold as a pair

Bilstein B8 6112 leveling kits are designed to provide more ground clearance, allow for larger tires, and increase wheel travel. Multiple snap-ring grooves in the body allow for different spring seat positions, providing 0-2.75 inches of front lift (depending on application). These kits consist of (2) 60mm shock absorbers combined with (2) custom matched cold wound coil springs and (2) billet aluminum spring seats. The large 60mm digressive piston allows for increased damping control for optimal on-road and off-road capabilities. Experience the legendary Bilstein off-road experience with the best direct fit spring and shock kit for your light truck or SUV.

Bilstein B8 5100 (Ride Height Adjustable) shock absorbers are designed for trucks and SUV's with a front OE coilover style suspension. Multiple snap-ring grooves in the body allow for different spring seat positions, providing 0-2.75 inches of front lift (depending on application). The monotube shock absorbers feature a 46mm digressive piston a with self-adjusting deflective disc valve setting. Bilstein B8 5100 (Ride Height Adjustable) shock absorbers provide increased wheel travel and improved handling. Utilizing a B8 5100 (Ride Height Adjustable) shock absorber is the easiest way to level out your vehicle.

Adjustable lower arm cam bolts. Comes in a set of 2. 2 sets are needed if replacing both lower arms.

Designed for adjusting the spring preload rings on 2.0" and 2.5" Fox, Sway-A-Way, King and Radflo coil over shocks.

*Please specify 2.0" or 2.5"

These bed low profile bed stiffeners bolt right on (nuts and bolts provided) and will add strength to the well known flimsy beds. Come painted black. $25 extra for black powder coat. Simi universal

This kit is for the hard core off road guys. Both prerunner and crawler alike. This kit relocates the custom Deaver leaf pack under the axle and will allow up to 19" wheel travel with the correct shock package. This is requires fabrication and we suggest the work be done by an experienced fabricator. We suggest running 2"+ wheel spacers with this kit. This kit is built to order

Kit includes the following:

1 pair custom Deaver leaf springs

2 pair CJD 12" shackles

2 pair rear relocating brackets with bushings

1 pair bash plates

1 pair leaf spring axle mounts

Grade 8 hardware

Shipping cost will be sent separately prior to shipping products.

***Roughly 10 week build time***

Nissan Frontier bolt on rear tube bumper. 1.75" .120 tubing.

Comes with led cube lights. Black powder coated.

Option: Dual swing out for spare tire and gas cans.

Shipping will be added after purchase and will be shipped freight.

**4-6 week build time ETA**

Give your 2005+ Nissan Frontier / Navara the best of the best with the Radflo 2.5″ diameter rear shocks.  Valving is customized to offer you incredible ride quality and performance.  These shocks are completely re-buildable and are the last shocks you will ever have to buy.  The shocks come with a remote reservoir to maximize travel and dampening.  Rear shocks are sold individually

Designed to replace stock rubber brake hoses on vehicles with increased ride heights. Steel Braided lines will not swell under increased braking pressure demanded by larger tires thus delivering a quick and positive response. Hoses comply with D.O.T. specifications and are packaged as a complete kit.

This spare tire mount is set up to mount to the utility tracks on the bed sides of the vehicle. This mount is adjustable for various tire sizes. Can be mounted anywhere on the railing. Welded mounts for cable lock to secure rim.

Whats included:

Mounting plate

Spanner wrench

Urethane mounting cone

Mounting bracket

Hardware

Comes painted black

Powder coat extra

10 leafs, military wrap, diamond cut ends, anti-friction pads and four piece bolt through retaining clips. Made to order. Lead time may very.

Add lift to the rear with these full leaf packs. Extra weight can be added to the springs as needed.

Sold as a pair.

Whats included:

10 leafs, military wrap, diamond cut ends, anti-friction pads and four piece bolt through retaining clips.

Note: Shipping cost will be sent in a separate invoice after purchase. we ship world wide

Bolt on rock sliders. Sold as pairs. 

What's included:

2- rock sliders

Grade 8 hardware

Powder coated black

"Does require drilling"

Stock replacement steel battery box for the Nissan Frontier, Xterra and Pathfinder.

This box bots into the stock position. Will work with both stock Group 24 and Optima style batteries.

Whats included:

Battery box

All needed hardwear

Options:

Painted

Powder coated black

CAD designed and made from 3/16" steel. These go right into place over the stock cam bolt holes. These are required to be welded on. They come in a full set of 8 mounts. So if you're looking to reinforce the stock holes, these will be your ticket.

What's included:

8- 3/16" steel plate gussets

Bolt on side steps. Sold as pairs. 

What's included:

2- rock sliders

Grade 8 hardware

Powder coated black

"Does require drilling"

Great way to improve the handling of your vehicle. These mounts are a bolt on setup. No welding required. (some grinding to the frame and drilling required)

Whats included:

2 - 2.0 bump stop upper moounts

2 - Lower bump stop pads

Hardware kit

Flag mount for the bed of your truck. Can be used with or without utili-track system. Made to fit any 1" diameter flag poles. 

What's included:

Flag pole mount

Mounting hardware

Come coated in Steel-It

Wore out upper control arms? This kit is what you need to rebuild and refresh them

What's included:

2 - 1" uniballs or Delta Joints

2 - 1" uniball snap rings

4 - 3/4" JMX right hand heims

4 - 3/4" jam nuts

This suspension kit was designed for the extreme off roader. This kit is fully CAD designed with 3/16” and 1/8” boxed plate. We changed the upper arm mounting location to improve the geometry of the full suspension cycle. This kit is capable of 19” of wheel travel with the 2WD system and 17” of wheel travel with the 4WD system. The 4WD kit comes with 300M race axles. It allows for the use of tires up to 37” in diameter and designed to run a 2.5 x 10” coilover and bypass shock with +1” rod ends.  **Note: This system does require fabrication work. We highly recommend to have the work done by a professional and qualified fabricator. This kit requires Titan hubs and brakes. We recommend 04-06 brakes for the Frontier to avoid rim spacing issues. 4wd requires the use of a Titan front differential and Titan CV's **

Specs:
Wheel Travel: 2WD 19”/ 4WD 17”
Minimum Rim Size: 17”
Maximum Tire Size: 37”
Track Width: 8” Wider Per Side
Coilover: 2.5 x 10” with +1” Rod Ends
Bypass: 2.5 x 10” with +1” Rod Ends

What’s Included:
Boxed UCA
Boxed LCA
Spindles
Billet Tie Rods
UCA/ Shock Mounts
Grade 8 Hardware
DOT Stainless Braided Brake Lines
Black Powder Coat
Extended 300M Axles (4WD Kit Only) (Axles Only Work with OEM CV’s)
Stainless Misalignments
All Needed Heims and Uniballs

Shipping cost will be sent separately due to weight

Looking to install a Titan Swap front end on your Frontier or Xterra but not break the bank? This is the perfect kit. Comes with everything needed to install. Just pair with your favorite pair of shocks/ coilovers and your ready.

Whats included:

CJD Titan swap tube UCA (pair) or SPC Titan swap UCA (pair)

Stock Titan LCA (pair)

Extended heim steering

Brake lines

R180 extended axles (4wd only)

This shock hoop is designed around our "underleaf kit" but will work with other leaf springs as well. It was designed to use an 18" 3.0 diameter bypass shock. Designed to cycle 19" of wheel travel with our "underleaf kit" A 16" shock can be used instead with longer rod ends on the bottom. This shock hoop is designed to be welded in. The shock hoop comes painted with Steel-it. Powder coat is extra. These are built to order.

What's included:

Shock hoop

2- lower shock mounts. 

Hardware

Bump stop brackets are completely bolt on and easy to install. 

Includes 

2) Bolt on brackets

2) Leaf Spring Strike Pads

2) Locked Offroad Threaded Hydraulic Bump Stops

All mounting hardware included

TECHNICAL SPECS:

Our Bump stops are designed to handle anything you can throw at them. They are built out of some of the highest quality materials to ensure a long shock life and reduce environmental wear.

We use Viton seals, 4130 Chromed polished shafts, Black Zinc coated steel shock bodies, 6061 Machined Aluminum coated in a deep black anodizing.

We stand behind our product 100% and offer a one year warranty on non wearable parts and a 6 month warranty on wearable parts.

Intended for off-highway use.

BUMP STOP:
2.0" diameter body 

1.26" shaft

2" or 4" stroke length

MOUNTING SLEEVES:
Heavy-duty bolt-on mounts for 2005 Nissan Frontier

The compression adjuster technology provides drivers the highest level of dampening customization and allows drivers to quickly fine-tune ride quality and performance for street or the most demanding off-road conditions, just with their fingertips.

Note: shock must have reservoir for compression adjuster to work.

The compression adjuster technology provides drivers the highest level of dampening customization and allows drivers to quickly fine-tune ride quality and performance for street or the most demanding off-road conditions, just with their fingertips.

Note: shock must have 2.5" diameter reservoir for dual speed compression adjuster

Cerakote is a ceramic based finish that can be applied to metals, plastics, polymers and wood. The unique formulation used for Cerakote ceramic coating enhances a number of physical performance properties including abrasion/wear resistance, corrosion resistance, chemical resistance, impact strength, and hardness. Each of these properties is rigorously tested to guarantee that Cerakote products remain at the forefront of the ceramic coatings market. Cerakote ceramic coatings utilize state-of-the-art technology to out-perform any competitive coating in both laboratory settings and real world applications.

Note: cost is per shock.

Want to build your own front bumper but not sure where to start? These are the perfect starting point to go off of. These are a bolt on application. You will be able to build of them and design your bumper however you want.  Mounts come raw.

Sold as a pair

If you're looking to Titan swap your Frontier (2005-2019) or Xterra (2005-2015) but retain the factory R180 front differential, this is the axle you need to retain your 4 wheel drive.  Axle comes ready to bolt up and go.

Sold each

They are made 2.5" wide springs, only enough to allow a snug fit so if you lose the center pin it won't fall apart on you. We make the perches slightly wider to add stability and fully rest the spring under the perch

Whats included:

• 2 - spring under leaf spring plates for 2.5" springs
• 2 perches for 3" axle tube and 2.5" wide
• 4 U-bolts 8" Long and hardware

Replaces the inner and outer tie rods. This kit comes with heims and both ends of the tie rods for a stronger and firmer feel. These are much stronger than stock tie rods and also eliminate bump steer.
Specs:
Stock Replacement
Bolt-On

What's Included:

Sold in pairs
CNC Rack Bolt
CNC Clevis
Billet Tie Rods
Grade 8 Hardware
Stainless Misalignments
All Needed Heims

This kit comes with both innner and outer heims needed to rebuild your steering system 

Whats included:

2- outer heims 

2 - inner heims 

4 - jam nuts

Replaces the outer tie rod/ ball joint. This kit will tighten up the front end and steering. Connects to the stock inner tie rod. Runs a heim outer.

Specs:
Stock Replacement
Bolt-On

What's Included:

Sold in pairs
Billet Tie Rods
Stainless Misalignments
Grade 8 Bolts
All Needed Heims

Nissan Frontier LED 3rd brake light.

This brake light is made to replace the stock 3rd brake light. The light will reuse the stock hardware for install.

This light comes with a few LED light options.

Option #1 Red/Yellow/Yellow/Red

Option #2 Red/White/White/Red

Option #3 No light

Light housing is 3D printed out of outdoor/ weather resistant materials. These housing are then painted black for added life.